This kit contains 15 x 1/2 circle micro sprays, 5 x full circle micro spinners, 20 of 300mm sprinkler risers, 20 of Stakes to support sprinkler risers, pipe fittings, assorted Garden Tap / water connection fittings, and 16 x clamps for pipe fittings.

The sprinklers in this Kit may even work all at once from the end of a garden hose. If you can’t run everything at once, you will have to break your sprinkler runs into 2 or more groups (see our simple bucket test flow calculation in the flow rate section of our DIY guidance page).

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust your sprinkler directions.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your garden being watered while you relax!

The post Kit of Garden micros sprays and sprinklers; contains 20 x sprinkler heads, risers, riser support stakes, pipe fittings, but no pipe appeared first on Designer Watering Systems.

This kit contains 4 x Rainbird 3500 pop-up sprinklers c/w 6 nozzle rack for each sprinkler, fittings for pop-ups, pipe fittings, assorted Garden Tap / water connection fittings, and 20 x clamps for pipe fittings.

Better watering Tip: Watering from an edge and throwing into an area using your adjustable angle sprinklers is better than one run of full circle (360º) sprinklers down the middle of an area, and space your sprinklers no further apart than their required throw. For example, if your sprinkler is to throw 5mt, then your next sprinkler should be less than 5mt away. Further apart will give a much reduced result.

The 4 sprinklers in this Kit may even work all at once frrom the end of a garden hose if using either the # 0.75 or # 1.0 nozzles (see our sprinkler info page for the Rainbird 3500 sprinkler). If you can’t run everything at once using the nozzles you have chosen for the distance you require, you will have to break your sprinkler runs into 2 or more groups (see our simple bucket test flow calculation in the flow rate section of our DIY guidance page).

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust sprinkler angles and distances.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your yard being watered while you relax!

The post Kit of 4mt – 7mt radius Pop-up Sprinklers; Contains 4 x gear-driven pop-ups, nozzle sets, pipe fittings, but no pipe. appeared first on Designer Watering Systems.

This kit contains 4 x Rainbird 5000 pop-up sprinklers c/w 12 nozzle rack for each sprinkler, fittings for pop-ups, pipe fittings, assorted Garden Tap / water connection fittings, and 20 x clamps for pipe fittings.

Better watering Tip: Watering from an edge and throwing into an area using your adjustable angle sprinklers is better than one run of full circle (360º) sprinklers down the middle of an area, and space your sprinklers no further apart than their required throw. For example, if your sprinkler is to throw 8mt, then your next sprinkler should be less than 8mt away. Further apart will give a much reduced result.

The 4 sprinklers in this Kit may even work all at once from the end of a garden hose if using the #1 smallest nozzle for a comfortable 7mt throw (see our sprinkler info page for the Rainbird 5000 sprinkler). If you can’t run everything at once using the nozzles you have chosen for the distance you require, you will have to break your sprinkler runs into 2 or more groups (see our simple bucket test flow calculation in the flow rate section of our DIY guidance page).

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust sprinkler angles and distances.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your yard being watered while you relax!

The post Kit of 7mt – 10mt radius Pop-up Sprinklers; Contains 4 x gear-driven pop-ups (their throw can actually screw all the way down to an ‘Off’ position), nozzle sets, pipe fittings, but no pipe. appeared first on Designer Watering Systems.

This kit contains 4 x Rainbird 1800 pop-up sprinklers with adjustable nozzle (0 – 360° / 0 – 4mt radius) already fitted, 25mt coil of 19mm pipe, fittings for pop-ups, pipe fittings, assorted Garden Tap / water connection fittings, and 20 x clamps for pipe fittings.

Better watering Tip: Watering from an edge and throwing into an area using your adjustable angle sprinklers is better than one run of full circle (360º) sprinklers down the middle of an area, and space your sprinklers no further apart than their required throw. For example, if your sprinkler is to throw 3mt, then your next sprinkler should be less than 3mt away. Further apart will give a much reduced result.

The sprinklers in this Kit should all work at once from your Garden Tap if nozzles are set to 180° or less, unless your water flow or pressure is quite low, whereby you may have to break your sprinkler runs into 2 or more groups. For example, sometimes flow or pressure can be quite low from a rear Tap, or through garden hose click-on fittings, or through a length of garden Hose. This is due to the smaller flow channels through garden hose, small pipe, and associated small fittings which all create flow restriction and pressure burn-off.

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust sprinkler angles and distances.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your yard being watered while you relax!

The post Kit of 0 – 4mt radius Pop-up Sprinklers; Contains 4 x pop-ups with adjustable angle & distance nozzle already fitted, pipe & fittings. appeared first on Designer Watering Systems.

This kit contains 4 x Rainbird 3500 pop-up sprinklers c/w 6 nozzle rack for each sprinkler, 50mt coil of 19mm pipe, fittings for pop-ups, pipe fittings, assorted Garden Tap / water connection fittings, and 20 x clamps for pipe fittings.

Better watering Tip: Watering from an edge and throwing into an area using your adjustable angle sprinklers is better than one run of full circle (360º) sprinklers down the middle of an area, and space your sprinklers no further apart than their required throw. For example, if your sprinkler is to throw 5mt, then your next sprinkler should be less than 5mt away. Further apart will give a much reduced result.

The 4 sprinklers in this Kit may even work all at once form the end of a garden hose if using either the # 0.75 or # 1.0 nozzles (see our sprinkler info page for the Rainbird 3500 sprinkler). If you can’t run everything at once using the nozzles you have chosen for the distance you require, you will have to break your sprinkler runs into 2 or more groups (see our simple bucket test flow calculation in the flow rate section of our DIY guidance page).

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust sprinkler angles and distances.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your yard being watered while you relax!

The post Kit of 4mt – 7mt radius Pop-up Sprinklers; Contains 4 x gear-driven pop-ups, nozzle sets, pipe & fittings. appeared first on Designer Watering Systems.

This kit contains 4 x Rainbird 5000 pop-up sprinklers c/w 12 nozzle rack for each sprinkler, 50mt coil of 19mm pipe, fittings for pop-ups, pipe fittings, assorted Garden Tap / water connection fittings, and 20 x clamps for pipe fittings.

Better watering Tip: Watering from an edge and throwing into an area using your adjustable angle sprinklers is better than one run of full circle (360º) sprinklers down the middle of an area, and space your sprinklers no further apart than their required throw. For example, if your sprinkler is to throw 8mt, then your next sprinkler should be less than 8mt away. Further apart will give a much reduced result.

The 4 sprinklers in this Kit may even work all at once from the end of a garden hose if using the #1 smallest nozzle for a comfortable 7mt throw (see our sprinkler info page for the Rainbird 5000 sprinkler). If you can’t run everything at once using the nozzles you have chosen for the distance you require, you will have to break your sprinkler runs into 2 or more groups (see our simple bucket test flow calculation in the flow rate section of our DIY guidance page).

Installation is easy: Decide on your sprinkler positions, dig your pipe trench from your water source to the furthest sprinkler location, select the relevant water connection fitting to connect your 19mm sprinkler pipe, roll out Pipe and connect sprinklers, clamp pipe to fittings, turn on the water, adjust sprinkler angles and distances.

If splitting is required, do a search in our shopping cart on items 10295 & 10290.

Finally, sit back and watch your yard being watered while you relax!

The post Kit of 7mt – 10mt radius pop-up sprinklers; Contains 4 x gear-driven pop-ups (their throw can actually screw all the way down to an ‘Off’ position), nozzle sets, pipe & fittings. appeared first on Designer Watering Systems.

Includes 4 station auto Rainbird Controller, 24Vac low voltage cable x 10mt, cable joiners, extra Tap and fittings connection, regulation Town water residential backflow prevention Valve, Pressure Pipe x 10mt, Pressure Pipe fittings, Valve manifold, 4 x auto low voltage 24Vac Solenoid Valves, 4 x connection to 19mm sprinkler Pipe, Plumbers Thread Tape.

Please note our pictured ‘easy to use’ telescopic grey manifold O’ring fittings became quite expensive and are now ‘no longer available’ to us at all. In their place, we are now supplying ‘swivel nut’ style O’ring manifold fittings.

If more Pressure Pipe fittings are required, got to Pressure Pipe fittings in our Shopping Cart.

The post Kit for 4 station automatic Control; contains Controller, auto Valves, Valve box, LV cable, Pipe & Fittings appeared first on Designer Watering Systems.

Includes 6 station auto Rainbird Controller, 24Vac low voltage cable x 10mt, cable joiners, extra Tap & fittings connection, regulation Town Water residential backflow prevention Valve, Presure Pipe x 10mt, Pressure Pipe fittings, Valve manifold fittings, 6 x auto low voltage 24Vac Solenoid Valves, 6 x connection to 19mm sprinkler Pipe, Plumber’s Thread Tape.

Please note our pictured ‘easy to use’ telescopic grey manifold O’ring fittings became quite expensive and are now ‘no longer available’ to us at all. In their place, we are now supplying ‘swivel nut’ style O’ring manifold fittings.

If more Pressure Pipe fittings are required, go to Pressure Pipe fittings in our Shopping Cart.

The post Kit for 6 station automatic Control; contains Controller, auto Valves, valve box, LV cable, Pipe & Fittings appeared first on Designer Watering Systems.

Includes 4 station auto Rainbird Controller, 24Vac low voltage cable x 10mt, cable joiners, extra Tap and fittings connection, regulation Town water residential backflow prevention Valve, fittings for Pressure Pipe (but no Pipe), Valve manifold, 4 x auto low voltage 24Vac Solenoid Valves, 4 x connection to 19mm sprinkler Pipe, Plumbers Thread Tape.

Please note our pictured ‘easy to use’ telescopic grey manifold O’ring fittings became quite expensive and are now ‘no longer available’ to us at all. In their place, we are now supplying ‘swivel nut’ style O’ring manifold fittings.

If more Pressure Pipe fittings are required, got to Pressure Pipe Fittings in our Shopping Cart.

The post Kit for 4 station automatic Control; contains Controller, auto Valves, Valve box, LV cable, Pipe fittings, but no pipe appeared first on Designer Watering Systems.

Includes 6 station auto Rainbird Controller, 24Vac low voltage cable x 10mt, cable joiners, extra Tap and fittings connection, regulation Town water residential backflow prevention Valve, fittings for Pressure Pipe (but no Pipe), Valve manifold, 6 x auto low voltage 24Vac Solenoid Valves, 6 x connection to 19mm sprinkler Pipe, Plumbers Thread Tape.

Please note our pictured ‘easy to use’ telescopic grey manifold O’ring fittings became quite expensive and are now ‘no longer available’ to us at all. In their place, we are now supplying ‘swivel nut’ style O’ring manifold fittings.

If more Pressure Pipe fittings are required, got to Pressure Pipe Fittings in our Shopping Cart.

The post Kit for 6 station automatic Control; contains Controller, auto Valves, Valve box, LV cable, Pipe fittings, but no pipe appeared first on Designer Watering Systems.